Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound

Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound
Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound
Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound

Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound

Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound. EIN (SMPTE): Attenuation: Noise Floor: Connectors.

Input Impedance: Output Impedance: Maximum Input Level: Max Output Level: Maximum Gain. 20Hz - 40kHz, +/- 3dB Mic/Line 5Hz - 40kHz inst. 1/4 unbalanced In and Out 600 O balanced, 10M O line 100 O bal. 7 5/8" x 1 5/8" x 5 3/8. 194 mm x 40 mm x 135 mm 2.5 lbs (1.135 Kg).

DIRECT DRIVE Tube Mic Preamp. Some states do not allow the exclusion or limitation of special, incidental or consequential damages so the above limitation or exclusion may not apply to you. Bellari is a division of. 20 dB PHANTOM +17 PAD PWR. We recommend that you take a moment and read this manual as it provides information that will help you in using your unit to it's fullest potential.

The MP110 provides clear sonic quality and perfor- mance for the working musician, studio operator or anyone who needs a preamp with the warm, smooth, analog sound. The unit uses a premium 7025 tube in a unique configuration to give smooth controllable gain. The unit has both XLR and 1/4 inputs and outputs with a 20 dB Pad and a Phase Reversal switch to adapt to any performing or studio situation.

Unpack and Inspect the MP110 package. Your MP110 was carefully packed at the factory in a protective carton. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. MODEL MP110 MADE IN USA. INPUT: 1/4 unbalanced and XLR balanced jacks for receiving incoming signals.

OUTPUT: 1/4 unbalanced and XLR balanced jacks for sending output- ting the signal to a recording device, mixer, amplifier, etc. Shown below is an example application for the DIRECT DRIVE.

Connect a microphone (dynamic or condenser) to the Mic Input, and an XLR or 1/4 cable to the Output. Connect the Output cable to a recording device. If the microphone is a condenser type, press in the Phantom Power switch. Sing or speak into the microphone at performance level and adjust the Gain control to a point slightly below clipping. Set the Volume control for a comfortable level for your recording device as indicated by it's level meters. PHANTOM PWR SWITCH: When pressed in, provides +48 volt phantom power to the Microphone Input. 20 dB PAD SWITCH: When press in, reduces the input signal by 20 dB. GAIN CONTROL: Adjusts the drive of the tube preamp stage. VOLUME CONTROL: Adjusts the overall signal level of the MP110. PHASE REVERSE SWITCH: When pressed in, shifts the output signal 180 degrees from the input signal. CLIP LED: Indicates clipping of the MP110 tube circuit (not output clipping). PWR LED: Indicates power is applied to the MP110. ATTENTION - DISTORTION POSSIBLE: The output stage of the MP110 may be overdriven by increasing the VOLUME control. This will cause a more harsh distortion than that of overdriving the tube circuit.

This may or may not be a desired effect. REWIND FAST FWD STOP PLAY RECORD EJECT.

This item is in the category "Musical Instruments & Gear\Pro Audio Equipment\Preamps & Channel Strips". The seller is "cindynana" and is located in this country: US.

This item can be shipped to United States.


Bellari MP110 Direct Drive Tube Mic Preamp + Original AC Adapter Great Sound